Warbird Information Exchange

DISCLAIMER: The views expressed on this site are the responsibility of the poster and do not reflect the views of the management.
It is currently Thu Mar 28, 2024 5:18 am

All times are UTC - 5 hours


Classic Wings Magazine WWII Naval Aviation Research Pacific Luftwaffe Resource Center
When Hollywood Ruled The Skies - Volumes 1 through 4 by Bruce Oriss


Post new topic Reply to topic  [ 5 posts ] 
Author Message
PostPosted: Wed Dec 02, 2015 7:30 pm 
Offline

Joined: Wed Dec 10, 2008 7:25 pm
Posts: 520
Location: Travis AFB
What are the best/quickest tools to use to cut aircraft aluminum. Any suggestions on tools? Specifically what blade types should I use? If I needed to cut wing from wrecked plane in the field, what should I use? gas powered tools or electric with generator? How about cutting wing when electric power is available? I'm trying to save a piece of history, but I can't save it all.


Top
 Profile  
 
PostPosted: Thu Dec 03, 2015 8:13 am 
Offline
1000+ Posts!
1000+ Posts!
User avatar

Joined: Wed Aug 18, 2010 12:51 pm
Posts: 1185
Location: Chandler, AZ
A reciprocating saw (ie. Sawzall) is probably your most versatile option. You can get fine tooth hacksaw blades in various lengths and shapes that will make short work of cutting up anything. One note. get at least three times as many blades as you think you'll need, and be ready to change them often, a bent or dull blade is less than safe or controllable, and generally frustrating. A couple of GP demo blades will come in handy in the field for clearing brush, cutting supports et cetera.

_________________
Lest Hero-worship raise it's head and cloud our vision, remember that World War II was fought and won by the same sort of twenty-something punks we wouldn't let our daughters date.


Top
 Profile  
 
PostPosted: Thu Dec 03, 2015 4:31 pm 
Offline

Joined: Fri Apr 14, 2006 11:42 am
Posts: 350
I just did this two weeks ago on a DC-3 wing tip: viewtopic.php?f=26&t=56964

Definitely borrow a generator for the job as electric tools are ideal for the job (don't forget the extensions cords). As mentioned by ALOHADAVE, a recip saw with plenty of replacement blades is good but also an angle grinder with a metal cutting blade will make short work of the task. It cuts through the aluminum like a hot knife going through butter! A couple of replacement blade wheels would also be a good idea. If you haven't used one before be very careful with an angle grinder though. They spin at over 1000 rpm so if a blade lets go it will throw the bits everywhere at high speed which is why they come with a protective guard. Also, don't place it down until it stops spinning. Learn how to use it safely and then go have some fun!


Top
 Profile  
 
PostPosted: Fri Dec 04, 2015 9:34 am 
Offline
3000+ Post Club
3000+ Post Club

Joined: Fri Jun 24, 2005 7:26 pm
Posts: 4961
Location: PA
Hi Dave,

What airplane are you working?

_________________
Shop the Airplane Bunker At
www.warbirdbunker.com


Top
 Profile  
 
PostPosted: Sun Dec 06, 2015 7:36 pm 
Offline
User avatar

Joined: Sat Sep 13, 2014 9:50 am
Posts: 85
When using metal cutting blades, have at least two or three teeth in the metal thickness while cutting, it will make the cut more effective and clean.

_________________
Volunteer
Yankee Air Museum


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 5 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 10 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group