MS24692-127DP Taper Pins needed
Fri Feb 24, 2006 4:54 pm
They used to be known as AN385H20P6. These guys are .750 long, drilled head, cad plated.
I’ve talked to Stealth, Reid, TPS, Saturn, Westco, AMP etc. with no luck.
About two dozen are used on the fuel selector control on a T-28. Any ideas?
I’ve talked to Stealth, Reid, TPS, Saturn, Westco, AMP etc. with no luck.
About two dozen are used on the fuel selector control on a T-28. Any ideas?
Fri Feb 24, 2006 5:53 pm
Jay-Tex Aviation is showing 20 of the old AN p/n in stock per the ILS (Inventory Locator Service) website. Ph 903-572-1985
Fri Feb 24, 2006 6:17 pm
Hey, thanks for the quick reply!
I was able to get someone on the phone there just now before the weekend. It looks they have about 12 left, so I still need to locate some more. I would actually like to get a hold of about 125 – 150 each.
I was able to get someone on the phone there just now before the weekend. It looks they have about 12 left, so I still need to locate some more. I would actually like to get a hold of about 125 – 150 each.
Fri Feb 24, 2006 8:33 pm
Try Lance Aircraft. If they were used on the T-6 they would likely have them. I bought some tapered pins from Aircraft Spruce about 6 months ago. Not sure if they are the same- they had 3/16 thread on the end.
Sat Feb 25, 2006 7:36 pm
if it helps i think the same pins are used on the p-40 and t-6.
Wed Mar 01, 2006 4:48 pm
Thanks everyone! The threaded taper pins are AN386. I picked up some from Spruce a while back.
I’m thinking of having AMP making a quantity of them.
I’m thinking of having AMP making a quantity of them.
Wed Mar 01, 2006 7:58 pm
Doing a search for "MS24692" I found the following:
From "Haystack Logistics":
From "Catalog Express":
These may not be in stock, but they may be able to order or make them for you (according to Uncle Sam).
Or, you could look at the spec and maybe buy a tapered pin with threads that will fit, cut off the threads and drill your own hole.
From "Haystack Logistics":
ACE FASTENER CO INC
T= (856) 9641785
F= (856) 9641162
http://www.acefastener.com/ Harvey Goodwin
President
ace@erols.com
DYNAMATION RESEARCH
T= (310) 4771224
F= (310) 4795656
http://www.dynamation.com Bernie Nolan
Sales Manager
bernie@dynamation.com
D AND T FASTENERS
136 MAIN ST
SPENCER, MA 015620092
Tel: (508) 885-2788 Fax: (508) 519-8132
From "Catalog Express":
Name: Allmetal Screw Products Corp
Address:
94A E Jefryn Blvd
Deer Park NY 11729
USA
Telephone: 631-243-5200
Telephone: 800-248-9755
FAX: 631-243-5307
Name: ASC International Inc, ASC Industries
Address:
1227 Corporate Dr W PO Box 200728
Arlington TX 76006
USA
Telephone: 817-640-1300
FAX: 817-649-2685
These may not be in stock, but they may be able to order or make them for you (according to Uncle Sam).
Or, you could look at the spec and maybe buy a tapered pin with threads that will fit, cut off the threads and drill your own hole.
Wed Mar 01, 2006 11:07 pm
Hey, bdk, I really appreciate those leads!
I’ll burn up the phone lines tomorrow and see what I can find.
I’ll burn up the phone lines tomorrow and see what I can find.